Dylan Ironside’s open J604 repo runs Omarchy on the 14-inch M4 MacBook Pro and grades it against macOS
The base M4 isn’t officially supported yet, but a self-described Omarchy M team member is publishing his patches, measurements and open bugs from his daily machine, including the first deep sleeps that come back.
Image: Dylan Ironside (X)
Dylan Ironside, who lists himself on X as part of the Omarchy M team, has been running Omarchy on his 14-inch MacBook Pro with the base M4 chip, and he is publishing the work in the open in IronsideXXVI/omarchy-j604. According to the README, the machine is a Mac16,1 with board J604 and the T8132 SoC, the same chip as the M4 MacBook Air, and it is his daily machine.
The rules are simple. The README says the repo uses “the official chain only”: omacom’s linux-aurora kernel with a J604 patch series, Aurora’s aura boot loader and U-Boot, the official installer, and the Omarchy edge channel, which he switched to on November 9, 2026. The repo carries only what the stock packages lack for this Mac. His current kernel build sits on the Aurora 7.3 base with 765 patches.
This isn’t official M4 support, and it isn’t something to install tonight. Omarchy 4.5 installs natively on M1, M2, M3 and Neo MacBooks. The README is clear that the “stock packages can’t boot this Mac yet,” that there are no prebuilt packages, and that “these builds target the J604 only” until the changes land upstream.
What makes the repo stand out is its scorecard. The README compares the J604 under Omarchy with macOS on the same machine, block by block, and the latest round on his kernel build 1.947 (measured November 16, 2026) puts the CPU at 99 % of macOS, RAM at 100 % and the display at 104 %. He flags that display figure himself as “a reading to repeat, not yet a gain.” The GPU sits at 41 %, and one reason is idle power: by his account the GPU never powers off at an idle desktop, while macOS keeps it off 99.9 % of the time.
In an update on X on November 14, 2026, Dylan listed what he says now works and matches macOS, including XDR being always on, True Tone adjusting the colour, Chromium hardware video encode, and the speaker amps and headphone chip running with macOS’s settings. He also measured light sleep at 0.98 W. The repo is more cautious on some of those points: its table still marks XDR/HDR as untested, and it says the Chromium video encoder is used only behind a feature that is off by default.
Sleep has moved fast since that post. On November 14 he wrote that deep sleep got all the way in but the wake reset the Mac 62 seconds later, adding: “A fix is ready for the next kernel I’m working on.” In aurora-silicon/linux#1961, opened November 15, he describes the J604’s first full deep sleep and wake on an RTC alarm, with display, Wi-Fi, Bluetooth, audio and NVMe back. About seven minutes later that machine cold-reset, and he says the cause is not proven yet. The README now lists deep sleep as the lid-close default and reports 7 of 7 deep sleeps waking on one of his builds. On a later build he measured 166 mW asleep. Only the timer wake has been measured so far: lid, key and power-button wakes are still untested.
The work is meant to flow upstream. “Changes go to the official repositories as reviewed pull requests, one topic at a time,” the README says, and it lists 42 open ones across Aurora and omacom repos. One has merged: aurora-silicon/linux#1392, a GPU fix for blank hardware-decoded video in mpv, merged by RyanTheTide on November 10, 2026. Edi Moldovan has opened a pull request to carry it into omacom’s kernel, which is still open. That deep sleep PR and his series for the six speaker amplifiers are still open too; the latter, per its own description, copies macOS’s register writes byte for byte but had not yet run on the J604 under Linux when it was posted.
Dylan is also generous with credit. The README says much of the kernel work is other people’s, carried with its authorship, and builds on Aurora Silicon (including DjDeveloperr’s M4 device trees), the omacom Omarchy for Apple Silicon team and Asahi Linux. If you own a J604 and want to follow along, the repo’s status table is the place to watch.
Source: https://x.com/IronsideXXVI/status/2121649659248623886
